Dopo un aggiornamento il 22/02/18 al riavvio non si apre la dash, il mouse è una x e nessuna funzione è possibile salvo il dx mouse sul desktop.Una finestra mi avverte di errore interno ma non riesco a leggere tutte le informazioni complete.Leggo:

Problem type Crash compiz-config-profile-setter crashed whith SIGABRT in ccs Ob...

e nel BootLog

Failed to start Raise network intern... see 'systemctl status networking service' for detail.

Attualmente per usare Ubuntu (16.04 LTS 4.4.0.116 generic) entro attraverso la modalità recovery mode,dpkg e poi ripristino. In questo modo dispongo di tutto il SO solo con risoluzione del monitor più bassa. Grazie

chiesto 20 Mar '18, 11:10

cikowalter's gravatar image

cikowalter
45446

modificato 23 Mar '18, 11:32

dadexix86's gravatar image

dadexix86 ♦♦
17.0k916161

1
  • cel'hai il file di configurazione di Xorg? /etc/X11/xorg.conf

  • in modalita' recovery riesci a attivare la rete?

(20 Mar '18, 20:28) sacarde sacarde's gravatar image

Grazie di aver risposto.In modalità recovery la rete funziona. Non ho il file Xorg.conf. Mi puoi accompagnare nell'intallazione?

root@walter-MS-7798:~# lspci | grep "VGA" 00:02.0 VGA compatible controller: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller (rev 09)

(21 Mar '18, 19:46) cikowalter cikowalter's gravatar image
1

potresti vedere se c'e' qualche servizio in errore:

accedendo alla console con ctrl-alt-f1

e poi eseguire: sudo systemctl --failed oppure: sudo journalctl -b -p err

(23 Mar '18, 11:02) sacarde sacarde's gravatar image

Versione di Ubuntu?

(23 Mar '18, 11:32) dadexix86 ♦♦ dadexix86's gravatar image

walter@walter-MS-7798:~$ sudo systemctl --failed UNIT LOAD ACTIVE SUB DESCRIPTION ● networking.service loaded failed failed Raise network interfaces

LOAD = Reflects whether the unit definition was properly loaded. ACTIVE = The high-level unit activation state, i.e. generalization of SUB. SUB = The low-level unit activation state, values depend on unit type.

1 loaded units listed. Pass --all to see loaded but inactive units, too. To show all installed unit files use 'systemctl list-unit-files'

walter@walter-MS-7798:~$ sudo journalctl -b -p err -- Logs begin at ven 2018-03-23 18:27:40 CET, end at ven 2018-03-23 18:41:59 CET mar 23 18:27:41 walter-MS-7798 systemd-udevd[248]: unknown key 'SYSFS{idVendor}' mar 23 18:27:41 walter-MS-7798 systemd-udevd[248]: invalid rule '/etc/udev/rules mar 23 18:27:59 walter-MS-7798 systemd[1]: dev-disk-by\x2dpartlabel-Basic\x5cx20 mar 23 18:28:15 walter-MS-7798 ntpdate[1265]: name server cannot be used: Tempor mar 23 18:28:15 walter-MS-7798 systemd[1]: Failed to start Raise network interfa mar 23 18:28:18 walter-MS-7798 NetworkManager[1190]: nm_device_get_device_type: mar 23 18:28:23 walter-MS-7798 hp[1444]: io/hpmud/pp.c 627: unable to read devic mar 23 18:28:23 walter-MS-7798 /hpfax[1442]: [1442]: error: Failed to create /va mar 23 18:28:55 walter-MS-7798 colord-sane[1369]: io/hpmud/pp.c 627: unable to r mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un mar 23 18:28:56 walter-MS-7798 gnome-keyring-daemon[1874]: GLib: g_hash_table_un

Ubuntu 16.04 LTS 4.4.0-116 (Prima dell'aggiornamento avevo tolto i file system più vecchi lasciando gli ultimi due). La rete in modalità recovery funziona bene malgrado l'error.

(23 Mar '18, 18:49) cikowalter cikowalter's gravatar image

hai disattivato da bios uefi: "secure boot" e "fast boot"

https://wiki.ubuntu-it.org/AmministrazioneSistema/Uefi

(23 Mar '18, 20:31) sacarde sacarde's gravatar image

@cikowalter perdonami ma è illeggibile. La prossima volta che devi scrivere codice usa il markup per il codice se, come in questo caso, è troppo lungo per stare in un commento, mettilo su un sito di pastebin e posta il link.

(24 Mar '18, 11:24) dadexix86 ♦♦ dadexix86's gravatar image
(24 Mar '18, 11:41) cikowalter cikowalter's gravatar image
  • "(Prima dell'aggiornamento avevo tolto i file system più vecchi lasciando gli ultimi due). "

con questo intendi i "kernel" ?

  • anche cambiando kernel hai gli stessi problemi?
(26 Mar '18, 21:39) sacarde sacarde's gravatar image

si, intendo i kernel. Anche con il pinultimo stesso risultato. Il desk si riempie delle icone come sempre ma il mouse si mostra con una x e la dash non è accessibile. Solo la tastiera e il dx del mouse.Devo uscire e riavviare in recovery mode.

(27 Mar '18, 11:17) cikowalter cikowalter's gravatar image

Questo è il log ottenuto dopo l'avvio di Ubuntu con l'errore interno. https://paste.ubuntu.com/p/7G2NwRnXdM/

(27 Mar '18, 21:32) cikowalter cikowalter's gravatar image
1

riesci a vedere se ci sono errori di Xorg ambiente grafico:

/var/log/Xorg.0.log

le righe che contengono "EE"

ci puoi accedere dalla consolle: ctrl-alt-f1

(02 Apr '18, 11:56) sacarde sacarde's gravatar image

Non riesco ad aprire il file /var/log/Xorg.0.log sia da console che con ctrl+F1. Neanche con sudo. Tuttavia, in modalità recovery, nel file /var/log/Xorg.0.log.old (ho controllato l'orario d'avvio del S.O.con errore interno) ho trovato il log di Xorg senza errori: https://paste.ubuntu.com/p/fxbQY7Nrc5/ (in questi giorni ho aggiornato anche i driver della stampante Brother ma erano di novembre e non sono la causa dell'errore. Peraltro la stampante funziona bene).

(03 Apr '18, 19:15) cikowalter cikowalter's gravatar image

con l'aggiornamento del nuovo 'kernel' è ripartito tutto correttamente. Grazie per l'aiuto.

(05 Apr '18, 19:32) cikowalter cikowalter's gravatar image

secure boot e fast boot sono già disabilitati.

coll. permanente

ha risposto 24 Mar '18, 11:45

cikowalter's gravatar image

cikowalter
45446

A me senza apparente ragione si crasha ubuntu 17.10 e appare a video:

BusyBox v1.22.1 (ubuntu1.1.22.0-19ubuntu2 build-in shell ash) Enter 'help' for a list of build-in commands (initramfs)

Secondo voi a cosa è dovuto? Fin'ora mi sono limitato a reinstallare... Finchè dura... Ci dev'essere un bug interno al kernel credo... :-( Grazie infinite per gli aiuti!

coll. permanente

ha risposto 02 Apr '18, 11:27

taoman9's gravatar image

taoman9
201

La tua risposta
abilita/disabilita anteprima

Segui questa domanda

Via email:

Una volta eseguito l'accesso potrai iscriverti a tutti gli aggiornamenti qui

Via RSS:

Risposte

Risposte e commenti

Basi di markdown

  • *corsivo* o __corsivo__
  • **grassetto** o __grassetto__
  • collegamento:[testo](http://url.com/ "titolo")
  • immagine?![alt testo](/path/img.jpg "titolo")
  • elenco numerato: 1. Foo 2. Bar
  • per aggiungere un'interruzione di riga, aggiungi due spazi a fine riga e premi «Invio»
  • è supportato anche semplice HTML

Tag:

×92

domanda posta: 20 Mar '18, 11:10

domanda visualizzata: 1,760 volte

ultimo aggiornamento: 05 Apr '18, 19:32

Chiedi è un servizio di supporto gestito da Ubuntu-it. Contattaci!

powered by OSQAPostgreSQL database
Ubuntu e Canonical sono marchi registrati da Canonical Ltd.