buona sera, dopo aggiornamento il wifi non rileva piu' il mio modem di casa, ma solo il cellulare in modaita' wifi hotspot...avete idee a riguardo?!

chiesto 23 Oct '19, 21:53

Maranza9000's gravatar image

Maranza9000
20123

  • quale scheda wireless hai? questa viene riconosciuta?

dmesg|grep wlan

  • vedi errori da:

systemctl --failed

journalctl -b -p err

(24 Oct '19, 08:36) sacarde sacarde's gravatar image

[ 23.017421] iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0

(16 Jan '20, 00:00) mmanuel2020 mmanuel2020's gravatar image

03:00.0 Network controller [0280]: Intel Corporation Dual Band Wireless-AC 3168NGW [Stone Peak] [8086:24fb] (rev 10) Subsystem: Intel Corporation Device [8086:2110] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <tabort- <mabort-="">SERR- <perr- intx-="" latency:="" 0,="" cache="" line="" size:="" 64="" bytes="" interrupt:="" pin="" a="" routed="" to="" irq="" 35="" region="" 0:="" memory="" at="" f1000000="" (64-bit,="" non-prefetchable)="" [size="8K]" capabilities:="" <access="" denied=""> Kernel driver in use: iwlwifi Kernel modules: iwlwifi

(16 Jan '20, 00:00) mmanuel2020 mmanuel2020's gravatar image

anchio la stessa cosa non si collega più alla wifi di casa, che qualche giorno fa andava egregiamente, provato a fare aggiornamento ma niente, mi dice attivazione della connessione di rete non riuscita. con altre wifi tipo con hotspot cellullare si collega subito come posso risolvere? grazie questa è la mia scheda03:00.0 Network controller [0280]: Intel Corporation Dual Band Wireless-AC 3168NGW [Stone Peak] [8086:24fb] (rev 10) Subsystem: Intel Corporation Device [8086:2110] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <tabort- <mabort-="">SERR- <perr- intx-="" latency:="" 0,="" cache="" line="" size:="" 64="" bytes="" interrupt:="" pin="" a="" routed="" to="" irq="" 35="" region="" 0:="" memory="" at="" f1000000="" (64-bit,="" non-prefetchable)="" [size="8K]" capabilities:="" <access="" denied=""> Kernel driver in use: iwlwifi Kernel modules: iwlwifi

coll. permanente

ha risposto 15 Jan '20, 23:57

mmanuel2020's gravatar image

mmanuel2020
2012

UNIT LOAD ACTIVE SUB DESCRIPTION
● snap.network-manager.networkmanager.service not-found failed failed snap.netwo ● systemd-backlight@backlight:acpi_video0.service loaded failed failed Load/S

LOAD = Reflects whether the unit definition was properly loaded. ACTIVE = The high-level unit activation state, i.e. generalization of SUB. SUB = The low-level unit activation state, values depend on unit type.

2 loaded units listed. Pass --all to see loaded but inactive units, too. To show all installed unit files use 'systemctl list-unit-files'. ...skipping... UNIT LOAD ACTIVE SUB DESCRIPTION
● snap.network-manager.networkmanager.service not-found failed failed snap.netwo ● systemd-backlight@backlight:acpi_video0.service loaded failed failed Load/S

LOAD = Reflects whether the unit definition was properly loaded. ACTIVE = The high-level unit activation state, i.e. generalization of SUB. SUB = The low-level unit activation state, values depend on unit type.

2 loaded units listed. Pass --all to see loaded but inactive units, too. To show all installed unit files use 'systemctl list-unit-files'. ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ...skipping... UNIT LOAD ACTIVE SUB DESCRIPTION
● snap.network-manager.networkmanager.service not-found failed failed snap.netwo ● systemd-backlight@backlight:acpi_video0.service loaded failed failed Load/S

LOAD = Reflects whether the unit definition was properly loaded. ACTIVE = The high-level unit activation state, i.e. generalization of SUB. SUB = The low-level unit activation state, values depend on unit type.

2 loaded units listed. Pass --all to see loaded but inactive units, too. To show all installed unit files use 'systemctl list-unit-files'. ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ Max buffer space per file (K): -p err

coll. permanente

ha risposto 15 Jan '20, 23:59

mmanuel2020's gravatar image

mmanuel2020
2012

@mmanuel2020

  • che vedi: dmesg | grep wlp3s0

  • se hai installato un kernel nuovo, da grub puoi avviare il kernel vecchio

  • che versione di ubuntu hai?

(16 Jan '20, 08:16) sacarde sacarde's gravatar image

buongiorno a tutti dopo giorni e giorni a chattare e cercare risposte finalmente https://chiedi.ubuntu-it.org/users/2263/sacarde mi ha dato l'indizio scrivendo questo"che vedi: dmesg | grep wlp3s0". scorrendo la sfilza di parole e numeri ho notato che c'erano problemi con l'ipv6. ho cambiato l'impostazione in automatico dhcp e magicamente funziona tutto come prima. ho visto che in molti in rete hanno questo problema. per favore aiutate quei poveri ragazzi indicandogli la via!!

coll. permanente

ha risposto 18 Jan '20, 12:13

mmanuel2020's gravatar image

mmanuel2020
2012

La tua risposta
abilita/disabilita anteprima

Segui questa domanda

Via email:

Una volta eseguito l'accesso potrai iscriverti a tutti gli aggiornamenti qui

Via RSS:

Risposte

Risposte e commenti

Basi di markdown

  • *corsivo* o __corsivo__
  • **grassetto** o __grassetto__
  • collegamento:[testo](http://url.com/ "titolo")
  • immagine?![alt testo](/path/img.jpg "titolo")
  • elenco numerato: 1. Foo 2. Bar
  • per aggiungere un'interruzione di riga, aggiungi due spazi a fine riga e premi «Invio»
  • è supportato anche semplice HTML

Tag:

×2,110
×511
×155

domanda posta: 23 Oct '19, 21:53

domanda visualizzata: 1,026 volte

ultimo aggiornamento: 18 Jan '20, 12:13

Chiedi è un servizio di supporto gestito da Ubuntu-it. Contattaci!

powered by OSQAPostgreSQL database
Ubuntu e Canonical sono marchi registrati da Canonical Ltd.